custom-aerospace-sensors-and-their-role-in-flight-testing

Quick Summary

An aerospace sensor turns a physical condition on an aircraft, such as pressure, force, position or temperature, into an electrical signal engineers can record during flight testing. Custom designs potentially fit tight mounting space, harsh vibration and unusual ranges that standard parts may not. Clear requirements on range, environment and documentation usually decide how well a sensor performs.

An engineer planning a flight test has a long list of conditions to measure and very little room to measure them. Every reading begins with an aerospace sensor, and when a standard part cannot fit the space or survive the environment, custom aerospace sensors could potentially close the gap.

Knowing what these sensors measure, and how a test environment differs from a laboratory, helps teams write requirements that a manufacturer can build to.

What an Aerospace Sensor Does During Flight Testing

A sensor converts a physical condition into an electrical signal. A pressure sensor reports how hard air or fluid pushes, a force sensor reports how heavily a part is loaded, and a temperature sensor reports how hot a component or its surroundings have become. The signal travels to data acquisition equipment, which records it for later analysis.

Flight test data lets engineers compare what an aircraft actually did with what analysis and ground testing predicted. That comparison is only as trustworthy as the sensor behind it. If a sensor drifts, picks up vibration or reads differently as it warms, the team may not be able to tell whether the aircraft changed or the sensor did.

The Main Types of Sensors Used in Aircraft Testing

Four families cover much of the measurement list on a typical test. Pressure sensors track outside air pressure, fluid pressure in hydraulic and fuel lines, and the pressure difference across a component.

Displacement sensors, including the LVDT (linear variable differential transformer), report how far a part has moved. An actuator rod or a control linkage is a common example, because its travel can indicate where a control surface is sitting. An LVDT does this without any rubbing contact between its moving core and its coils, which could potentially help with long service life.

The remaining two families, load, force and torque sensors and temperature sensors, appear in the sections below, because each one raises its own design questions.

Why Standard Sensors Sometimes Fall Short

Catalog sensors are designed for broad use, and flight test campaigns often present constraints outside that range. Mounting space may be only a shallow pocket, weight may be tightly limited, and the pressure, load or travel to be measured may sit between standard ranges. Connectors, cable exits and housing shapes may also need to match existing structure.

Consider a load, force and torque sensor placed inside a compact linkage. If its shape forces the linkage to change, the measurement may no longer represent the original design. A custom shape could let the sensor carry the load without altering how the part behaves.

Many gaps close with a modified-standard design, which keeps a proven sensing approach but changes the range, connector or housing. A fully one-of-a-kind design becomes worth considering when the geometry or environment leaves no standard starting point. Stellar Technology offers both routes.

Environmental Demands in Flight Testing

Vibration and shock come first. Engines, airflow and landings all shake a sensor, and a design with delicate internal parts could produce false readings or fail early. How the sensor is mounted matters nearly as much as how it is built.

Temperature is the second demand. Components can sit near hot equipment on one flight and in cold, thin air on the next. A precision temperature sensor can record those swings directly, and that record may help engineers judge whether other sensors shifted with temperature.

Altitude adds a third. Ambient pressure falls as an aircraft climbs, so a pressure sensor that references the surrounding air can behave differently from a sealed one. Choosing the reference type deliberately avoids confusion when the data is reviewed later.

Finally, electrical noise from nearby equipment can disturb small signals. Shielded cable, careful grounding and a suitable output type could all reduce that risk.

What Custom Sensor Engineering Involves

A custom project follows a path that is easier to follow when laid out in order:

  • Define the requirements. Range, overload, environment, mounting space, output signal and electrical connection are written down together.
  • Design and prototype. Engineers choose the sensing element, housing and materials, then build early units to test against the requirements.
  • Build and calibrate. Each finished sensor is checked against known references so its output corresponds to the pressure, force, position or temperature applied.
  • Calibration records travel with the sensor so the test team can keep them alongside the data.

Engineering, machining and calibration work at Stellar Technology are handled in-house, which could shorten the loop between a design question and a tested answer.

Quality Systems

Stellar Technology began in 1991 with an initial focus on the aerospace market, and its quality system is certified to ISO 9001:2015 and AS9100D. Those certificates describe the quality management system. Product-specific approvals apply only to the series named on each approval, so scope is worth confirming for the exact sensor being considered.

Some aerospace and defense work also involves export-control rules. For that reason, the details of a particular test campaign are best discussed directly with an engineering team rather than described in public.

Questions to Settle Before Specifying a Test Sensor

A short list of answers makes a custom request far easier to quote and build:

  • Range and overload. What is the highest value to measure, and what spikes could the sensor see beyond it?
  • Which temperatures, vibration levels and fluids will the sensor meet?
  • Mounting and size. How much space, weight and cable length are available?
  • Output and connection. Which signal type and connector does the data system accept?
  • Calibration and lead time. Which records are needed, and when does the test begin?

FAQs

What types of sensors are used in aircraft?

Beyond the four families above, aircraft also carry accelerometers for vibration, airspeed sensors based on pressure differences, angle-of-attack sensors and fuel level sensors. No single campaign is likely to use every one of them. Settling the measurement list early matters, because it fixes which sensors are installed and how many channels the data system must record.

What are four types of sensors?

By measured quantity, the four most common groups are pressure, temperature, displacement and force sensors. Sensors can also be grouped by sensing principle, such as strain gauge or inductive, or by output signal, such as voltage or current. Datasheets usually mix these groupings, so check which one a manufacturer is using before comparing two products.

What is an air sensor?

Air sensor is a loose label for a device that measures air pressure, air temperature or airflow. The term has no single fixed meaning, so it helps to ask exactly which property is being measured. Naming the exact property first points to a pressure sensor, a temperature sensor or another device as the starting point.

How does a proximity sensor work?

A proximity sensor detects whether an object is near without touching it, commonly by sensing a change in an inductive or capacitive field. It usually reports presence or a threshold rather than a measured distance. An LVDT is different because it reports how far a part has moved as a continuous value, which suits position tracking better than a simple near-or-far signal.

Talk with Stellar Technology, the Application-Solution Source, about a custom sensor built around your flight test requirements.

Leave a Reply

Your email address will not be published. Required fields are marked *